570-367-1106
570-367-1106
Gutter Installation · Central Pennsylvania
Seamless Gutter, Rolled On-Site and Hung Right
We form 5" and 6" seamless aluminum gutter right in your driveway — no seams, no leaks, no waiting on a supplier.
-Licensed & Insured · PA158334
-Free Estimates
-Roofing & Gutters Under One Roof
Gutters aren't complicated. You need water off your roof and away from your foundation, you'd like it to look decent doing it, and you'd rather not think about it again for twenty years.
The difference between gutter that does that and gutter that doesn't comes down to how it's formed and how it's hung — seams every ten feet, hangers spaced too wide, pitch eyeballed instead of measured. None of it shows up on installation day. It shows up two winters later, in the stain running down your siding.
One Contractor for the Roof and the Gutter
We roll-form gutter on-site with our own machine, so each run comes off in a single continuous piece cut to your eave. The only seams are at corners and outlets, where they belong and can be sealed properly.
We install 5" and 6" seamless aluminum. Five-inch handles most homes around here. Six-inch is the call for a big roof plane, a steep pitch, or heavy tree cover — wider trough, bigger downspout, fewer clogs. We'll tell you which one your house needs, and if it's the cheaper one, that's what we'll say.
And we're a roofing company that does gutter, not a gutter company with a ladder. Drip edge, fascia, and gutter all get done by the same crew that knows how they're supposed to meet.
Neighbors, not salesmen. We'll tell you what you need and nothing more.
What Goes Up on Your House
Formed On-Site
Our roll-former travels with the crew. Your gutter is made in your driveway, cut to your measurements, the day it goes up. Nothing gets pieced together to fit.
5" and 6" Aluminum
Five-inch for standard residential runs, six-inch for larger roofs, steep pitches, and heavy water volume. Aluminum won't rust and holds a finish for decades.
Color Selection
A range of baked-on enamel colors to match trim, fascia, or roof. It's a small thing, but it's the difference between gutter that disappears and gutter you notice.
Hidden Hangers, Screwed
Hangers fasten into the fascia with screws, spaced for our snow loads — not nailed in and hoped for. A properly hung run doesn't sag under a February ice load.
Measured Pitch
Every run is pitched to the outlet so water actually leaves. No standing water, no mosquito breeding, no ice sitting in the low spot all winter.
Downspouts Sized to the Roof
Downspout count and placement are figured off the roof area feeding them, and discharge is aimed away from the foundation — not just dropped at the corner because that's where the corner is.
Worth Doing at the Same Time
Our roll-former travels with the crew. Your gutter is made in your driveway, cut to your measurements, the day it goes up. Nothing gets pieced together to fit.
We're an Alu-Rex certified installer, which means the guard isn't a screen laid on top — it's an integrated system that replaces the hanger entirely and strengthens the gutter itself.
T-Rex®
Continuous Hanger™ with built-in leaf filtering. Supports up to 250 lbs of snow and ice load. The right answer for most homes with moderate tree cover.
DoublePro®
Continuous Hanger™ with ice and pine needle protection. Supports up to 425 lbs and moves up to three times the drainage volume. Built for heavy tree cover, pine needles, and the ice we get out here.
If you're on the fence, we'll walk your property and tell you honestly whether your tree situation warrants it.
How a Gutter Job Goes
Step 01
We Measure
We walk the house, measure every run, count the corners, and figure out where the water needs to go. You get a written estimate with the gutter size, color, downspout locations, and price. No pressure, no expiring discount.
Step 02
We Form and Hang
The crew shows up with the roll-former and makes your gutter on-site. Runs go up in single pieces, hangers get screwed into solid fascia, pitch gets set to the outlets, and downspouts get run and secured.
Step 03
We Clean Up and Test
Scrap and fasteners get picked up, the ground gets swept, and we run water through the system to confirm it drains the way it should before we leave.
Common Questions
What does "seamless" actually mean?
The gutter is formed as one continuous piece for the full length of each run. Sectional gutter comes in pre-cut lengths that get joined every ten feet, and each joint is a place water can eventually work through. Seamless gutter only has seams where a run meets a corner or an outlet.
Should I get 5" or 6"?
Five-inch is right for most homes around here. Six-inch makes sense when you have a large roof area draining to one run, a steep pitch that moves water fast, or enough tree cover that clogging is a regular problem. We'll tell you which your house calls for when we measure.
How long does installation take?
Most residential jobs are done in a day. Larger homes, complicated rooflines, or gutter with guard can run into a second day. We'll give you a realistic window when we quote it — not a best-case guess.
Can you match my trim color?
We stock a range of baked-on enamel colors and can usually get close or exact. Bring us a sample or we'll pull a color off your existing trim when we measure.
Do you install gutter on new construction and additions?
Yes. New builds, additions, garages, pole barns, outbuildings — if it has a roof and an eave, we can hang gutter on it. Working with a general contractor is routine for us.
Do I need gutter guard?
Not everyone does. If you're under heavy tree cover — especially pine — it pays for itself in the cleanings you don't have to do or pay for. If you've got open sky and no trees, it's optional. We'll give you a straight answer for your property.
Can you do gutter if I'm not replacing my roof?
Of course. Gutter is a standalone job. But if your roof is close to due, it's worth asking about doing both — there's efficiency in one crew, one mobilization, one cleanup.
Do you offer financing?
Yes. Ask about it when we quote the job.
Where We Work
We're based in Howard and we hang gutter across Centre, Clinton, and Lycoming Counties — State College, Bellefonte, Pleasant Gap, Milesburg, Lock Haven, Mill Hall, Beech Creek, Jersey Shore, Williamsport, Montoursville, and the towns in between. If you're not sure whether we come out your way, call and ask. We probably do.
Good Gutter Isn't Complicated.
It's Just Done Right.
Free estimate, honest recommendation, and gutter formed in your driveway by the same crew that does our roofs.
Double L Roofing
Double L Roofing provides roofing services in Howard, Bellefonte, State College, Lock Haven, and surrounding areas throughout Centre, Clinton, and Lycoming Counties.
182 Tree Line Ln, Howard, PA 16841
570-367-1106
PA158334
Services
Shingle Roofs
Metal Roofs
Gutters
Roof Repairs
Company
About
Projects
Contact Us
Instant Estimate
© 2026 Double L Roofing. All rights reserved.